Avoid Refrigerator Repair With Proper Care

Refrigerator repair is one of the responsibilities that come with owning such an appliance. However, there are ways to keep the repair bills down and the repair man away. Some simple rules to the upkeep of a refrigerator can serve to keep that fridge running smoothly and efficiently for a long time to come. Most of these at home repairs require no purchase other than your basic household supplies and maybe once and a while the replacement of a part or two kenmore refrigerator repair altadena.

One of the most important at home refrigerator repair tips that you can learn is to clean the outside of your fridge as well as the inside. Keeping the clutter away from the outside of your fridge space and making sure that there is no build up of dust around the base and back coils can assure a properly balanced temperature within. You see, a refrigerator works at cooling something but releasing hot air into the outside atmosphere through the vents and coils around its frame. If these components are blocked it will not be able to properly and efficiently release the hot air, causing the temperature to rise inside. This will cause the gears and compressors to work harder than normal which will eventually lead to them burning out-more often than not quicker than should be.

Another helpful tip to keep in mind is: overstocking the fridge is bad for it. When there is too much food in body of the fridge it again will have to work extra hard to release the right amount of heat which can lead to mechanical difficulties. While this won’t pose a problem right away, in the long run it will have shortened the life of a, suppose-to-be durable appliance. There is plenty of room in a refrigerator to stock what is necessary and if you happen to buy in bulk you might want to look into freezing some of the products that can be. If your refrigerator is keeping a balanced temperature, not only will the contents taste and smell better they will be healthier as well. You can never go wrong with safety.

Not properly taking care of your appliance can lead to some costly refrigerator repairs. If a compressor burns out it is going to require replacement which is pricey, but if your coils or the like stop working then you face having to replace your refrigerator entirely which can cost hundreds to thousands of dollars. It would be better in the long run to simply take the time to provide some upkeep to it instead of waiting for something to happen. In cases such as this, foresight and proper care is definitely more practical then hindsight and lackadaisical attitudes. No matter how you look at it taking the above simple steps-cleaning inside and out, not overstocking- will lead to less problems in the long run. If you are prepared for problems to arise with your refrigerator, why not take it one step further and take steps to prevent such problems.

Pressure Washer Parts And Supplies Are Crucial

Pressure washers are big business these days as they are the most effective way of dealing with a number of household chores. Washing away dirt, removing grime and dust or obliterating mud are just some of the tasks where pressure washers can have a huge impact. Whether you are looking to freshen up your car, your driveway, the outside of your home or your business, these high-pressure washers get the job done with the minimum of fuss and effort.

In the current economic climate maytag washer repair pasadena, having this tool and knowing how to use it properly may help a person to obtain some extra income. The versatility of a pressure washer means that there are a million and one jobs that can be carried out with it but not everyone has the time to use their washer on a variety of jobs or even the money to buy a high quality pressure washer. This opens up the potential in owning your own washer.

It doesn’t take a long time to become proficient in the use of a pressure washer, there is not too much to using it. However, there is definitely a knack to using it properly and this is where a trained person can have an advantage over other users. If you were to use these to bring in some extra money, there is a need to be professional when using it. This means providing a courteous service to people and you need to make sure the washer is in good working condition. This is where availing yourself with parts and supplies can ensure you provide the best service possible.

There are many great washer attachments that can make a job easier or indeed more fun. This is something to bear in mind if you want the family to pitch in and help with chores. Some of the spare parts you could use on a washer include spray nozzles, rotating nozzles, swivels, unloaders, lances and even trigger guns. Depending on what you are washing or whereabouts you are working, these supplies can make a big difference to the overall task. Knowing where to obtain washer supplies and spare parts is also important because there are a number of different components used in a washer. All it takes is for component to stop working and the pressure washer could be out of action.

Knowing where affordable and reliable parts and supplies can be sourced will make life a lot easier and will ensure the best value and usage is obtained from the washer.When thinking about parts and supplies, it is not important to think about the make and model of washer you have but the surfaces that you will be working on. This may have an impact on the sort of parts you are looking for so always try to plan ahead. If a pressure washer was to be used for just one car or location, a specialist range of supplies could be bought and attached but if it is for general use, the more standard attachments should be considered.

High Quality Washing Machine Repairs That Make Appliances Last

Household appliances are items in the home that a lot of people simply expect to be there and expect to work. The reality is that these appliances do not last forever and sometimes they will either break or need repairing.

A lot of people want to ensure that they have these appliances working at all times and this means that whilst a lot of the time it might be a simple fix that is needed to get the washing machine working again, they will simply purchase a new one because it requires less thought. A better option would be to look for engineers to carry out affordable washing machine repairs, which means they do not have to go through the expense of purchasing a new product ge washer repair pasadena.

The reality is that washing machines are over worked on a daily basis. People put in their dirty, smelly and oily clothes, expecting them all to come out as clean as ever. The great thing is, the majority of the time they will actually come out clean. The problem is though, there are a lot of parts that can break or wear out when put under extensive strain, which is where washing machine repairs come in.

The fact is that a lot of people are not mechanically or DIY minded. This means that when washing machine repairs are needed, they do not really know where to start. Even if the problem is an extremely quick and easy fix, it might not flag up with the individual and the likelihood is that they will throw it away and purchase a new one.

Luckily, there are plenty of companies that take the stress away by providing services such as washing machine repairs. What they do is come out and conduct a survey and from this survey they can determine whether the machine needs to be fixed or whether the client would be much better off simply purchasing a new one. What this means is that the consumer will be informed of the most financially viable option, instead of trying to make this decision by themselves.

Using these companies is stress-free if you pick the right one, for a start, they will come directly to the clients’ door, so there is no need for the client to leave the comfort of their own home. Another good aspect of these companies is the fact that they work on an extremely tight schedule. This means that they try their hardest to respond to calls as quickly as possible, causing the client as little inconvenience as possible.

Is Your Dryer Vent Cleaner Omitting A Very Crucial Step?

Most everyone now recognizes the critical importance of having their dryer vent system cleaned every few years. The Consumer Product safety Commission estimates that there are over 15,000 fires in the U.S. due to clogged dryer vents. Most people are under the assumption that those fires are due mainly to the vent line being restricted by a build up of lint, but this is only partially true. A clogged vent pipe can indeed restrict the airflow enough to cause the dryer to overheat and cause a fire but the main cause of most dryer fires is actually due to lint, hair and dirt build up inside the dryer cabinet.

How does lint actually get inside the cabinet you might ask lg dryer repair pasadena? Well, there are a couple of ways in which this can happen. Although the ducting inside a dryer should normally be tight and sealed properly, there are instances where the joints become loose or disconnected, which in turn allows the lint to escape. More often than not, the accumulation of lint is the result of the louvered panel in the back of the dryer sucking in “Make Up Air” to feed the dryer blower. You see, your dryer exhausts a large amount of air to the outside of the house while in operation, this air must be replenished from the laundry room continuously otherwise the blower will be starved for air. The air gets drawn into the back louvers of the dryer and unfortunately carried along with it is the surrounding dust, dirt, dog hair etc. All this junk coats the inside of your dryer and is highly flammable. Your dryer either has an electric heating coil or a gas burner. Lint is extremely combustible, if it comes in contact or is in close enough proximity to these heat sources then it can possibly catch fire. Dryers do have safety mechanisms built into them that will not allow the dryer to operate if it starts to overheat but these have nothing what so ever to do with the sudden ignition of lint inside your dryer.

So here’s the point I want to get across. Of course, it’s imperative to have your dryer vent system cleaned periodically but you should also make certain that your dryer cabinet gets thoroughly cleaned in addition. Most dryer vent cleaners won’t even go near the dryer, this is where it is up to you to inquire as to the extent of the their procedures. You may have to contact an appliance repair person, in addition to having a dryer vent cleaner come out. It will be an added expense but by not having it done it could put your property and the safety of your family at risk. You are also most welcomed to stop by my site for additional tips that I’m sure you will find very helpful.

 

How to Prevent Clothes Dryer Fires

Few people realize the importance of dryer safety. According to the U.S. Consumer Product Safety Commission, there are an estimated annual 15,500 fires, 10 deaths and 10 injuries caused by dryer fire. Several hundred people a year are also subjected to carbon monoxide poisoning from improper dryer safety measures. The financial costs come to nearly $100,000,000 per year. In some cases faulty appliances are to blame, but many fires can be prevented with proper dryer safety precautions whirlpool dryer repair pasadena.

Why Dryer Fires Occur

Lint accumulation and reduced airflow feed on each other to provide conditions ripe for a fire. Lint is a highly combustible material, which, interestingly enough, is one of the ingredients in a recipe for home-made fire starters. A number of dryer vent problems contribute to this.

A growing problem

Traditionally, most clothes dryers were in the basement. However, nowadays many newer homes tend to have dryers located away from an outside wall in bedrooms, bathrooms, kitchens and hall closets. These new locations mean dryers tend to be vented longer distances and vents are generally installed with sharp turns and bends to accommodate the structure of the home. As a result, dryer vents are harder to reach, and also create more places for lint to gather. The ideal solution is to have short, straight, dryer duct venting. However, a dryer vent booster, while not the ideal approach, can improve your dryer venting in cases where your venting is longer and/or has more bends than it should. In addition to creating a fire hazard, if the venting is too long and/or has two many bends, it will cause your dryer to take much longer than necessary to dry loads.

Inside the Dryer

Lint is the biggest culprit here. As you know from cleaning out your lint filter, dryers produce very large quantities of lint. Most people assume their lint traps catch all the lint, and that all they need to do is clean them out after each load. However, a significant amount of this lint is not caught by the lint trap and builds up inside the dryer-even on the heating element! If you are skeptical, try this experiment: pull out the lint trap and look underneath it- you may find large mounds of lint staring at you. Lint can build up on the heating element and in other places inside the dryer, causing it to overheat and possibly catch fire. As a rule, a fire starts from a spark in the machine. However, improper clothes dryer venting practices outside the dryer can play a key role in this process.

Outside the Dryer

There are many improper dryer vent practices which restrict airflow and lead to lint buildup, the two main preventable causes of dryer fires.
Some of the most common and important dryer vent mistakes are:

1. Dryer vents are too long and/or have too many bends, but don’t use a dryer duct booster, resulting in lint buildup. When it comes to dryer vents, shorter and straighter is better.

2. Use of flammable, flimsy plastic or foil duct extenders. Only metal vents should be used, which is what most manufacturers specify. Metal vents also resist crushing better than plastic and foil, which allows the air and lint to be carried out of the system. Reduced airflow from build-up or crushing can cause overheating and wear out the clothes and appliance faster. In fact, many state and local municipalities have placed requirements on new and remodeling projects to include all metal dryer venting.

3. Inadequate clearance space between dryer and wall. Many people create problems by putting their dryer right against the wall, crushing the venting material in the process. The cumulative effect of reduced airflow and the resulting lint build-up prevent the dryer from drying at the normal rate. This causes the high temperature limit safety switch to cycle on and off to control the heater. Most high temperature limit safety switches were not designed to continuously cycle on and off, so they fail over a period of time.

4. Failure to clean the dryer duct.

Your Dryer May be Failing If:

The clothes are taking an inordinately long period of time to dry, come out hotter than usual or if the vent hood flapper doesn’t open. Maintenance is needed in these cases.

Only You Can Prevent Clothes Dryer Fires

Proper Installation & Choice of Building Materials

1. Make sure the dryer duct is made of solid metallic material. Both vinyl and foil are combustible and spiral-wound surfaces tend to catch lint more readily.

2. The dryer duct should vent to the exterior and in no case should it vent to the attic or crawlspace. Avoid the use of inside heat recovery diverter valves or termination boxes, which do not comply with current standards.

3. Avoid kinking or crushing the dryer duct to make up for installation in tight quarters -this further restricts airflow. If you really want to save the extra space, the Dryerbox is a new invention that allows the dryer to be safely installed against the wall.

4. Minimize the length of the exhaust duct (maximum recommended lengths depend on a number of factors, such as number of bends, and vary by model-check with your manufacturer for their specifications). If this is not possible, you can install a dryer duct booster.

5. If at all possible, use 4-inch diameter vent pipe and exterior exhaust hoods that have openings of sixteen square inches or more, which offer the least resistance to air flow.

6. Don’t use screws to put your vent pipe together – the screw shafts inside the piping collect lint and cause additional friction.

Keep the Dryer Duct in Good Condition

Best Tips on Repairing a Washer

As a do-it-yourself expert you know that there is nothing more satisfying than a job well done. You also know that doing your own repairs can save you a lot of money. To repair a washer all you need is a screwdriver,some pliers, and some basic guidelines and you are well on your way to becoming a home washer repair expert.

The first step is to try to figure out where the problem is Appliance Repair Van Nuys. If the washer doesn’t run and you don’t hear any sound coming from it, there are several things you must check. Make sure that the washer is plugged in, then check the breakers to see if maybe the circuit has overloaded. If none of those seem to be the problem, and the water is turned on, check to see if the water hose is connected and turned on. If the motor is not running at all, it may have to be replaced.

If the washer makes noise then at least the motor is getting sufficient power to it. This means that a different problem is occurring. Check to see if the washer is filling up with water, and that the water is filling up to the right level. If it is not filling properly, check to make sure the water supply is turned on all the way. It is also a good idea to check the pressure to make sure it is correct. Check the drain hose and make sure that it is seated properly at the top of the inside tub. It is a good idea at this point to check the drainage of the water hose. Make sure that it is in the correct position of 38 inches or level with the top of the washer. Be certain that it is not allowing the water to drain as it fills. The last thing to check is to make sure that the hose is not pulled too tautly near the main drain or the water will not drain properly. Make sure that the gap around the hose is not clogged, or the water will siphon out from it instead of going in.

If the issue is the water or the cycles, then the timer needs to be replaced. Write down the brand and model number before you buy the new timer to make sure it will work with your washer. Making certain that the washer is unplugged, remove the knobs and the control panel. Look for the wire that connects the timer to the washer and push them back if they are too long. As you disconnect each wire from the old timer, connect it in the same place on the new timer to make sure they are connected properly.

If after troubleshooting you find that the water level is the problem, you may need to replace the inlet valve. You can find the hoses at the back of the washer once you remove the back panel. Disconnect both hoses from the washer and from where they connect on the outside of the washer. Find the wires on the terminal and disconnect those as well. Remove the screws that hold the valves in place on the washer. You need to check the coil wire by tapping it lightly to see if it has come lose. If that doesn’t work, replace it by installing a new one in the opposite procedure that you used to remove the old.

If your washer won’t agitate, it is a simple job to repair or replace it. First make sure that it isn’t cracked, as your clothes can get caught up in it. If it just has jagged pieces, you may be able to sand them smooth again. If that doesn’t solve the problem, then just unscrew the cap, pull the old agitator off, slide a new one on, and secure it with a new cap.

Tips on Repairing Your Appliances

When it comes to appliance repair there are very few instances wherein we get a warning as to what’s going to happen. It’s usually something that happens at the spur of the moment and the appliances break down just when we need them the most. Well, this should be obvious as they would only break down when we need it right?

Tips on repairing your appliances

No matter what the appliance or the reason of its destruction you’re going to need to repair it. There are plenty of things that you could do in order to get it repaired. However, there are a few tips that you need to keep in mind:

Check for warranties

Before you go ahead and try to repair anything on your own Jennair Appliance Repair Los Angeles, you need to make sure that the appliance isn’t covered by any kind of warranty. If at all it’s covered under warranty and you meddle with it, the contract would be null and void.

If at all the appliance is covered by a warranty this is what you need to do:

Call the company; clarify the reason of the breakdown of the appliance and what you need them to do for you. Next would be to get them to come over to your home or you would have to take the appliance to them on your own and then proceed accordingly.

Repair it yourself

If at all you’re sure that your appliance isn’t covered by any kind of warranty you should try fixing it yourself before you hire any professional help as that’s going to be totally free. Usually if you take a look at the owner’s manual you would find enough information which would help you repair the appliance all on your own.

In some cases you may not have the manual or the manual may not provide you with the information that you need. In such cases all you need to do is look up some videos or articles online and you would find all the help you need as there would definitely be others who’ve had the same problem and have done something to help others in the same situation out.

Hire someone to do the job for you

There are plenty of reliable appliance repair companies that would be located in your city. All you need to do is find someone who’s trustable and hand over the appliance to them. Make sure to check out their prices and reviews before choosing them though.

Top 5 Benefits of Hiring an Appliance Repair Man

We all have household appliances that we rely on daily and it is frustrating when one of them breaks down. Firstly, we do not want to pay a fortune replacing these items especially when modern technology is so costly. Washing machines, cookers and dishwashers are among the most expensive household items that people often replace without finding out if they could be fixed first. An appliance repair man will know what is wrong with your appliance and then advise you on a plan of action.

Below are the top 5 benefits of hiring an appliance repair man.

1. It’s cheaper. More often than not, repairing the appliance costs less than buying a new model. Unless you are an expert in this field, you will not realise that the problem might be small, could be fixed and costs very little Washer Repair Los Angeles.

2. It’s quicker. If you search for a high quality local repair man, chances are that you will receive a much speedier service. Shopping for household appliances can be a very drawn out process, you will need to find a reasonable quality model, try to get the best price and finally have it delivered. For those of you that have work and family commitments, this will not be an ideal as you just don’t have the time.

3. It’s done for you. How does it feel whenever you know something is being dealt with and you don’t have to lift a finger? It is much more reassuring to know that no extra effort will be required on your part and you can get on with your day.

4. It’s safer. At one stage in our lives, we have all tried a bit of D.I.Y so it’s not surprising how many people try to save money by repairing the appliance themselves. Unfortunately, household appliances have become much more technological and more difficult to fix. Hiring an appliance repair man will eliminate any danger of electrocuting yourself or suffering any injuries. Unless you know what you are doing and are sure you can fix it, it is safer to call a professional.

5. The problem can be resolved. Any household appliance is usually very important for your day to run smoothly and so you will want the problem resolved as soon as possible. An appliance repair man will know when he calls out, how to best deal with the issue. You will then know whether you should buy a new appliance or have it mended. Either way, at least the problem will be resolved.

Overall, there are key benefits in hiring an appliance repair man or at least seeking some free professional advice before wasting time, money and energy in buying a brand new one.

When to Call Appliance Repair Service Personnel

There is a certain time of year when everything just seemed to go kaput. And if you live in San Diego, you know that the climate can sometimes pose a threat to your appliance. Cords fall off just about every time; you turn the air conditioner on only to find out it’s not properly cooling anymore. Is it really just that time of the year or does your appliance imply something — like they are more than willing to be put into rehab. Now the question arises as you ponder on how to restore the health of your rusty yet reliable domestic devices that you have been with all these years, “Should I really call for an appliance repair service in San Diego Maytag Appliance Repair Los Angeles?”

If you are too emotional to part from your appliance or just happened to be on your budget, calling an appliance repair service in San Diego, CA is the only way you can kick your appliance back to its job — again. Though some will readily call for help, most of us would have that nagging thought of trying to fix something on our own. There will be always that DIY-er inside us that can’t help but assume that we can do everything. Can you really do it? In times when you’re torn between your pride and crying for help, here are questions that can help you determine the answer for all these.

Do I really need to get it done fast? If you are hosting a party the next day and your fridge broke down, you probably need help fast. And in times like this, you may want to call an appliance repair service within San Diego and not anywhere else. If time is a factor, you certainly don’t want to dilly dally, thinking about how will you, yourself, get it done. Determine if you have time to plan, do research, start, and, of course, complete the project. If not, then all have to do is phone a reliable appliance repair service in San Diego and wait ’til the repairman comes.

How much do I know about it? Have you done any electrical project before? Do you know much about the appliance that’s needed to be rehab that you want to do it yourself? If you’re attempting to learn about repairing appliance, you may not want to do it with your broken refrigerator. Major appliance like refrigerator and air conditioner is essentially knotty, you need days of training before you can pin down what has caused them to malfunction.

There are some things we can handle, and if we’re not trained to fix things, repairing major appliance is not one of them. If you have been scratching your head for more than five minutes, then it’s high time that you phone the pros for help.

Front Loading Washer & Dryers – Is it Time to Upgrade?

For the past five years or so, high efficiency (H.E.) front loading washers and dryers have been all the rage. Not only do they look neat with all the digital features, they’re cool with new colors – red, blue, silver — never seen before in our hum-drum laundry rooms. Things are looking up!

What is a High Efficiency Front Loading Washer?

First off, what is a H.E. front loading washer? Most are front loading washers like the type you’d see in a laundromat. They are characterized by: 3

A Rotating Drum that tumbles clothes through less water Dryer Repair Los Angeles. This compared to a top loader which rubs clothes against an agitator in a tub full of water.

A High Pressure Spray Rinsing that saves water and helps get soap out of clothes.

A faster Spin Cycle that cuts down on water and causes clothes to be “drier” out of the washer.

A More Efficient Motor and Automatic Sensing that conserves water and energy.

Top Loading Machines

Top loading machines are the most common type of washing machines. Laundry is deposited and withdrawn from the top of the machine. Top loading machines are best for people who have back problems as it’s easier to get to the load without bending or kneeling over. These machines are less costly and tend to be more reliable. So why “throw in the towel (and your socks too!)” and upgrade your laundry machines now? Let’s delve further into high efficiency front loading machines.

H.E. Front Loading High Efficiency Machines

H.E. Front Loading machines have been around enough now that there is ample information available on their benefits and drawbacks:

BENEFITS:

– Save Money – these machines use far less water and electricity than top loading machines. H.E. machines only fill up partially with water. They lift the clothes up and drop them back into the water, instead of totally emerging them in water as do top loaders.

Studies show that H.E. machines use up to 50% less water and 50-65% less energy than top loading machines. 5 The U.S. Department of Energy calculates savings of up to $50 a year in utility costs. 3 A $100 a year savings in utility costs is even possible with the best energy efficient machines as compared to your old 15 year old top loading washing machine. 3

– Load Capacity – most H.E. machines can handle more clothes with capacities ranging from 12-20 pound loads.

– Cleaner Laundry – because of their tumbling and drop action, they can clean clothes more fully. Reports from consumer reports and CNET reviews confirm clothes are cleaner.

– Drier Clothes Out of the Washer – due to moisture extraction in the spin cycle. This also aids with reduced energy consumption. Drier clothes from the washer mean less time for clothes to dry, which equates energy consumption reduction.

– Good for the Environment – due to less energy consumption and water usage. A family of four could reduce their water usage by up to 8,0000 gallons a year using H.E. machines. 4

– Stackable – Front loaders can be stacked, making more for space in smaller laundry rooms.

– Home Network Integration – believe it or not, models such as the LG SteamWasher can be integrated into your home network and can show you the washer’s progress on your computer!

– High Capacity – purchasing a large capacity H.E. machine will allow you to double the amount of clothes you can put into the washer. A person with a family of 5, is now able to wash all the bed linens in one load — a feat not even thought possible with a top loader.

NOTE on Detergent: High Efficiency (H.E.) machines work best with low-foaming, high-efficiency detergent which is made specifically for H.E. machines. These detergents are formulated for low water levels and tumbling action. H.E. detergents are comparable in price to normal detergents. Using regular detergents in H.E. machines creates too many suds which will make it harder to get the soap out of the clothes.

DRAWBACKS:

– Vibration – some H.E. models vibrate excessively during the spin cycle. It depends where you place your washing machine. If you place it on concrete, the vibration will be pretty much absorbed. However, putting it on a wood framed floor will cause the vibrations to be more noticeable. Newer models include reduced vibration features.

– You Snooze You Lose – if you forget to put something in the washer after you pressed the start button – the item is going to have to wait until the next laundry load. The door locks so that water doesn’t pour out onto your floor. NOTE: Some models now offer a pause button which allows you to add extra laundry after the load has started.

– Digital Breakdowns – some of the higher end models use digital screens which allow you to customize your washing experience. However, digital components can break down or be confusing and this can greatly decrease your front loader experience. Repairing digital components can be costly.

– Mold Growth – there have been numerous complaints about strange odors coming from these machines. H.E. machines harbor moisture which promotes mold growth, hence the noticeable smell. Mold growth can be prevented by leaving the washer door open after a load is done and through a little preventative maintenance. To decrease the presence of mold, add 3/4 cup of bleach to your white laundry cycle to remove any build up in the machine.

– Run Time – H.E. machines tend to take longer – expect at least one hour for the wash to be completed. Expect 1 1/2 hours for the special allergen cycles.

Important Features

When shopping for a H.E. front loading machine, here are some features to keep in mind:

– ENERGY STAR – ensure your washer is ENERGY STAR – which means the government has declared it to be an energy efficient appliance. While ENERGY STAR does not label dryers, be sure to choose one with a moisture sensor so that the machine will automatically shut off once the clothes are dry.

– Capacity – determine the size of washer needed ahead of time. A larger family points to a larger capacity needed.

– Several Water Level Options – or Automatic water Level Sensing. Water level options allow you to reduce water usage by adjusting water to the size of your load.

– Yellow Energy Guide Label

Choose a model with a high Modified Energy Factor (MEF) and a low Water Factor (WF). This is a valuable tool in determining how much energy it takes to use the machine and how it ranks compared to other models. The label also provides an estimate of annual operating costs.

– High Spin Speeds – helps to wring out the water from the clothes before going into the dryer.

– Steam – steaming your clothes rather than washing them is more efficient as it loosens up dirt and freshens up and sanitizes clothes. Steaming clothes also reduces water usage as the tub is not filled with water. Both washers and dryers can offer this feature, but not all models offer steam. 2

– Quiet – front loaders are amazingly quiet. Yes, you still hear them but you’ll notice a big reduction in volume. Also, because front loaders balance the load better, you won’t hear that loud banging noise like you do with top loaders when the laundry load becomes unbalanced.

– Delayed Start – washing machines have now joined the fray of delayed starts just like their oven and dishwasher counterparts. With some models, you can set your H.E. machine to begin washing a load at a certain hour. You can start it at 4am to be ready for the dryer by the time you awake, which reduces the amount of time wet laundry sits in the washer.

– Allergy Clean – some models offer a special high temperature cycle designed to reduce certain allergens. It helps to reduce dust mite populations and is particularly useful for bedding and pillows.

– Automatic dispensers – fill up the dispensers with detergent, fabric softener, and bleach to automatically dispense at the right time. This is HUGE for people used to top loaders. With a top loader, many of us put the detergent in first, then fill the tub with water, then put the clothes in. This takes a good amount of time and you need to be around to complete the steps. Not so with a front loader. The front loader takes in the detergent along with water and ensures the detergent is thoroughly mixed before combining it with the clothes.

– Extra Rinse Cycle – for those people who are extra sensitive to detergent being in their clothes.

– Pedestal with Bottom Drawer – pedestals can be purchased separately for approximately $250 each to make it easier to reach inside your washer and provide for extra storage. As pedestals are hollow inside, they will not help much against a heavily vibrating machine. Some people build platforms out of wood or concrete to add height to their washer and dryer rather than purchase pedestals.